how to attach 4x4 to slab

Attaching wooden posts to a poured concrete slab | Fine ...

I’d like to put a pergola on this slab. What would be the best way to attach the posts to the slab? I think I remember seeing a product that you pour into concrete after drilling a hole in it, when it dries you can drive regular hardware into it. I was thinking of using that and attaching L brackets to the slab and then to the posts….

Get Quotes / Contact Us

How To Attach The Table Legs With Simple And Easy Steps

Step 7: Attach the top of the table leg into the square surface plates. The last step of this method is to screw the top of the table leg into the square surface plates. You can twist many times to make them tighten. After everything is done, you need to check the attachment between the tabletop and the table legs to make sure if they are ...

Get Quotes / Contact Us

joinery - Attaching Legs to a Table - Woodworking Stack ...

Attaching Legs to a Table. ... The top went pretty well I think, but now it's time to attach the legs and I feel like there has to be a better solution than the one I'm thinking about using. So the 4x4 butts up directly to the 2x10, with the 2x4s at right angles. Everything is reasonably square, but the brackets that I'm planning on using have ...

Get Quotes / Contact Us

4x4 To Concrete Slab - Carpentry - Contractor Talk

Re: 4x4 To Concrete Slab How about using some 1/2" all-thread, drill the concrete and epoxing the all-thread in leaving it stick up about 9". Then attach the posts like you would newel posts on a set of stairs.

Get Quotes / Contact Us

Attaching 4x4 posts to concrete | Terry Love Plumbing ...

I will be putting a 4x4 vinyl sleeve over the 4x4 treated post. I am aware of the bracket that you fasten to the concrete, then to the post. Using that method concerns me about how stable the top of the post will be.

Get Quotes / Contact Us

Attaching 4x4 posts to concrete | Terry Love Plumbing ...

The steel tube is the same dimension as the 4x4 posts. You might be able to get less expensive pipe and put spacers on it to fill out to the 3.5" square dimension. If you have a very good concrete slab you can use a 6" square base plate and anchor it with a single 5/8" fastener in the center.

Get Quotes / Contact Us

What is the best way to attach 4x4 posts to a concrete ...

I would like to add a few posts with railing to our concrete patio. The posts don't need to support any weight they are simply decorative for our front patio.

Get Quotes / Contact Us

attach 4x4 post to concrete slab - outdoor deck manufacturer

How to Fasten a 4X4 Post to a Concrete Slab | eHow Jun 23, 2015 ... Fastening posts to concrete involves drilling or boring into the existing concrete in order to safely attach the posts.

Get Quotes / Contact Us

Assembling Your Homemade Box Deer Hunting Stand

In this step, you attach (3) 48" 2x4 pieces and (1) 48" 1/2" OSB (or plywood) strip as shown on the left. The 48" pieces should extend out exactly 1 1/2" beyond the edges of the 4x4, as shown.The purpose of the lower 2x4 and OSB strip is for fastening to your tree.

Get Quotes / Contact Us

How to Build 4x4 Poker Table Legs

The legs outlined in this section are extremely inexpensive and, when done correctly, can look quite nice. The legs are built out of nothing more than simple 4x4s that you can buy at any home improvement store and should take no longer than an hour to construct.

Get Quotes / Contact Us

Build a Farmhouse Table - Instructables.com

Introduction: Build a Farmhouse Table. By kentdvm Follow More by the author: ... For a 34x72 inch table and 4x4 legs, these apron lengths inset the legs roughly 2" on all sides. The wood is 3/4" to 1" thick rough-cut wood from our old barn. ... I decided I would attach the table top using metal clips (pic 3) and cut a kerf for the ...

Get Quotes / Contact Us

How to attach two 4x4's?| Off-Topic Discussion forum

I am going to attach 2x4's on the legs at the head and foot running from the left leg to the right leg. There will be one on both the inside and outside of both the head and foot. Additionally, there will be three to four 2x4's running underneath from the left "frame 4x4" to the right one.

Get Quotes / Contact Us

How to Attach Table Legs: 12 Steps (with Pictures) - wikiHow

Depending on the look you're going for, I would suggest building a frame that you can just place the slate in, and then attaching the legs to the frame. Alternatively, there is a matching brass piece (usually) near the hanger bolts at a hardware store.

Get Quotes / Contact Us

Attaching 4x4 Posts To A Concrete Porch. - Building ...

Once bolted to the slab, your post sits in the U and is screwed from the sides. You'll need to face around the bracket if you dont want so see it when done. It will also have a standoff so that your post sits up off the slab to prevent moisture damage.

Get Quotes / Contact Us

carpentry - How can I attach legs to a table? - Home ...

A heavy duty lag/stud bolt is screwed into the table leg. The upper inside corner of the 4x4 leg can be cut at a 45 degree angle as shown below to make it easier to drill the lag bolt into the leg. The skirt boards that go between the legs are notched and an angled cross member is glued and screwed into the inside face of the skirt boards.

Get Quotes / Contact Us